Synology DS920+ Setup [Ultimate Hardware Installation Guide]

Are you unable to understand how to execute the Synology DS920+ setup process? Did no guide you have come across so far help you to do so? Well, thankfully your hours of browsinghas redirected you to the right one. Here, starting from top to bottom, we have talked about every aspect of the hardware installation in detail. With that said, do not let go of any more time prior to reading this blog further.

What are the Package Contents?

The setup process will get started by unpacking the DS920+ system. Along with the main unit, you will find an AC power cord, AC power adapter, around 18 screws for 2.5 drives, 2hard drive tray keys, and 2 RJ-45 LAN cables. Make sure that you pull out every accessory carefully. Any damage can cause installation issues for you.

With these accessories, you will also get your hands on the optional accessories. You can now make changes to your Synology NAS to fit different business environments. To know which optional accessories you will get, read on:

• Memory Module: DDR4 non-ECC un-buffered SO-DIMM 4GB
• Fan: System Fan 92*92*25 mm
• Disk Tray: 3.5″/2.5″ HDD Tray With Lock
• Adapter: Adapter 100W Level VI

Synology DS920+ Setup [Installation Process]

1. Install Drives

Start the process by removing the drive trays, pulling on the circled area. Once done, load the drives in the trays. In case you using 3.5 drives, remove the fastening panels. You can do this from the side of the tray. Once done, place the drive in the tray. Then, connect the panels in order to secure the drive in its position.

In case you are using 3.5 drives, then repeat the first step, i.e. removing the drive trays by removing the fastening panels. Ensure that this again gets done from the side. Once done, insert the drive where the tray is has a blue indicator on it. Done with this too? Good. Now, turn the tray upside down and at last, tighten the screws.

Look for the empty drive bay and in it, connect the drive. Once done, push it back. You need to hear a click sound when the tray successfully gets locked into its place. It is recommended that you repeat the steps given above in order to setup the other drives. Now, continue reading and learn about how to get further with the Synology DS920+ setup process.

2. Start Synology NAS

Get access to a LAN cable in order to make a connection between the Synology NAS DS920+ system, router, switch, and hub. Take our advice and put only that cable to use which does not have any cuts. Once you have assured this, connect one end of the power adapter to the port located on NAS. Next, you need to connect the other port to the power outlet.

Locate the power button on the NAS. Once you find it, press it, and do it carefully. Pat yourself on the back because now your Synology NAS DS920+ is online and can be detected from a network computer. Continue reading and learn about how you can add a memory module to the NAS system in a hassle-free manner.

How to Add Memory Module to NAS?

The first and foremost thing which you need to do is, shut down the Synology NAS system. Disconnect all the cables from your Synology NAS DS920+ system in order to prevent as much damage as possible. Once done, remove the hard drive trays from the bays of the drive. Can you see an empty memory slot on the right side of the system? Good.

The next step in line is for you to add a new memory module. This ought to be done into the empty slot. For this, you ought to set the gap between the connectors of the module. This needs to be done with the notch on the empty slot. Once done, connect the memory module to the slot and it is suggested that you ensure, the module has been inserted properly.

Push down the memory module and wait to hear the click sound.Connect the drive trays back to the drive bays. Reverse the first step, which is, reconnecting the cables. Hit the power button located on the Synology NAS DS920+ system in order to turn it on. Make sure that it gets properly powered on.

The Bottom Line

And it is a wrap. In this manner, you will be able to complete the Synology DS920+ setup process using the above-mentioned step-by-step instructions in a hassle-free manner. Now, you can access the Synologylogin page and manage the settings of the Synology NAS system. To learn about how you can do this in detail, it is recommended that you read the information which is given in the product or user manual of your NAS system.